Features Main Components 1,200W (dynamic) Class D power amp 15-inch woofer with a 3-inch voice coil Frequency response: 35 to 160 Hz Max SPL: 126 dB 2 combo XLR-¼-inch line inputs and two XLR direct outputs Controls Easy-to-use DSP performance presets: Normal — typical FOH use Mo’ Bass — extended low-end performance Locate—adjusts performance for arrayed and non-arrayed applications Normal — non-arrayed applications Cardioid — create a ground-stacked cardioid subwoofer array (using two of the same model subwoofer) Endfire — create an endfire cardioid subwoofer array (using two of the same model subwoofer) Fully variable lowpass filter (sets the upper frequency limit/crossover point) LP filter presets for use with AIR15, AIR12, and AIR10 LP filter presets for use with AIR15, AIR12, and AIR10 Alignment delay — adds delay time relative to full-range speaker Polarity — invert the polarity of the summed input signal Convenience Features 2 comfortable ergonomic side handles Ground-stack provisions Caster provisions (caster kit included) Defeatable front-panel LED Rugged, texture-painted, birch enclosure Tour-grade, 17 gauge steel grille

Features 10-inch glass-composite low-frequency transducer 250 watt, Class AB biamplification Input gain control (-30 dB to +6 dB, continuously variable) and continuously variable lowpass filter (50 Hz to 130 Hz) Switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent to the main monitors Momentary footswitch (included) bypasses the subwoofer, highpass filter, and Sub Out Left and right, balanced XLR and ¼"TRS and unbalanced RCA main inputs

Electronics Voltage 100-120V Wattage LF Amplifier - 80W, HF Amplifier - 65W Hardware Cabinet Material Vinyl-Laminated, Medium-Density Fiberboard Miscellaneous Connection Type IEC Monitors Protections RF Interference Output-Current Limiting Over-Temperature Turn-On/Off Transient Subsonic Filter External Mains Fuse Audio Controls Volume Range: A-Type TaperMF Control: Variable (-6 to +6 dB)HF Control: Variable (-6 to +6 dB)Low Cut: Flat, 80 Hz, 100 HzAcoustic Space: Flat, -2 dB, -4 dB Peak SPL 106 dB (at 1 Meter) Crossover Frequency 2.4 kHz Monitor Inputs 1 x Balanced XLR, 1 x Balanced 1/4"TRS, 1 x Unbalanced RCA HF Transducers 1.25” Silk Dome Tweeter LF Transducers Dual 6.5" Frequency Response 45 Hz – 22 kHz Input Impedance 10 kΩ Monitor Amplifier Power LF Amplifier - 80W, HF Amplifier - 65W Specifications Input Impedance 10 kΩ

The R65's custom 6.8-inch Air Motion Transformer (AMT) ribbon tweeter responds to the subtlest waveforms and the highest frequencies, resulting in a greater sense of"air"and"space"that is characteristic of audiophile recordings. Custom coated, woven, 6.5-inch LF drivers produce a more dynamic output than conventional designs, thanks to the rigid cone's ability to maintain a more constant dispersion pattern across its frequency response range. The result is transparent sound with narrow vertical dispersion, which reduces undesirable reflections, and broad horizontal dispersion for a wide sweet spot. Driven by a 150W Class D amplifier, the biamped R65 delivers an open, clear, and less fatiguing listening experience. Features 2-way active AMT design provides articulate high-frequency response and wide stereo imaging Custom-designed, 6.8-inch, AMT ribbon tweeter responds to the subtlest waveforms and the highest frequencies 6.5-inch Kevlar LF drivers provide transparent mid- and low-frequency reproduction for clean sound and punchy bass Biamped 150W RMS (LF = 100W, HF = 50W), Class D power amplifier with switching power supply Acoustic Space settings (Linear, -1.5 dB, -3 dB, -6 dB) compensate for room placement Balanced XLR and ¼-inch TRS plus unbalanced RCA inputs provide flexibility for seamless integration into any environment RF interference, output current limiting, over temperature, turn-on/off transient, and subsonic filter protection Interchangeable black faceplate included Energy Conservation Mode (with enable/disable) lowers standby power to <0.5W External mains fuse Power: 100-120V, 60 Hz or 220-240V, 50 Hz